# generated by PrusaSlicer 2.3.3+win64 on 2021-11-07 at 01:40:26 UTC

[print:0.20mm QUALITY @MEGA - Copy]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 5
bottom_solid_min_thickness = 1.2
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 45
brim_width = 8
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 0
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.4
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.4
fill_angle = 45
fill_density = 10%
fill_pattern = grid
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.4
first_layer_height = 0.2
first_layer_speed = 75%
gap_fill_speed = 30
gcode_comments = 1
gcode_label_objects = 1
infill_acceleration = 1500
infill_anchor = 5%
infill_anchor_max = 10%
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_only_where_needed = 1
infill_overlap = 10%
infill_speed = 70
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 10%
ironing_spacing = 0.08
ironing_speed = 15
ironing_type = solid
layer_height = 0.2
max_print_speed = 200
max_volumetric_speed = 0
min_skirt_length = 25
notes = JohnsProfile-26-10-2021
only_retract_when_crossing_perimeters = 1
ooze_prevention = 1
output_filename_format = {input_filename_base}_{layer_height}mm_[filament_type]_Vyper_{print_time}_{used_filament}meters_{total_weight}grams_[notes].gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.4
perimeter_speed = 70
perimeters = 3
post_process = 
print_settings_id = Johns-PrusaSlicer-PLA-Profile-26-10-21
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 1
skirt_distance = 5
skirt_height = 1
skirts = 4
slice_closing_radius = 0.049
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.4
solid_infill_speed = 70
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.4
support_material_interface_contact_loops = 1
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 1
support_material_interface_speed = 70
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_speed = 70
support_material_synchronize_layers = 0
support_material_threshold = 65
support_material_with_sheath = 0
support_material_xy_spacing = 75%
thin_walls = 1
threads = 8
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 40
top_solid_layers = 5
top_solid_min_thickness = 1.2
travel_speed = 120
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[print:StudioZombie_VyperV1]
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonic
bottom_solid_layers = 5
bottom_solid_min_thickness = 1.2
bridge_acceleration = 1000
bridge_angle = 0
bridge_flow_ratio = 1
bridge_speed = 45
brim_width = 8
clip_multipart_objects = 1
compatible_printers = 
compatible_printers_condition = 
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 0
draft_shield = 0
elefant_foot_compensation = 0.2
ensure_vertical_shell_thickness = 1
external_perimeter_extrusion_width = 0.4
external_perimeter_speed = 40
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.4
fill_angle = 45
fill_density = 15%
fill_pattern = grid
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.4
first_layer_height = 0.2
first_layer_speed = 75%
gap_fill_speed = 30
gcode_comments = 1
gcode_label_objects = 1
infill_acceleration = 1500
infill_anchor = 5%
infill_anchor_max = 10%
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.4
infill_first = 0
infill_only_where_needed = 1
infill_overlap = 10%
infill_speed = 70
inherits = 
interface_shells = 0
ironing = 0
ironing_flowrate = 10%
ironing_spacing = 0.08
ironing_speed = 15
ironing_type = solid
layer_height = 0.2
max_print_speed = 200
max_volumetric_speed = 0
min_skirt_length = 25
notes = StudioZombie3D-Vyper-2021-11-06
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_[filament_type]_Vyper_{print_time}_[notes].gcode
overhangs = 1
perimeter_acceleration = 800
perimeter_extruder = 1
perimeter_extrusion_width = 0.4
perimeter_speed = 70
perimeters = 3
post_process = 
print_settings_id = Johns-PrusaSlicer-PLA-Profile-26-10-21
raft_layers = 0
resolution = 0
seam_position = aligned
single_extruder_multi_material_priming = 1
skirt_distance = 5
skirt_height = 1
skirts = 4
slice_closing_radius = 0.049
small_perimeter_speed = 30
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.4
solid_infill_speed = 70
spiral_vase = 0
standby_temperature_delta = -5
support_material = 1
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 1
support_material_contact_distance = 0.16
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.4
support_material_interface_contact_loops = 1
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 1
support_material_interface_speed = 70
support_material_pattern = rectilinear
support_material_spacing = 3
support_material_speed = 70
support_material_synchronize_layers = 0
support_material_threshold = 65
support_material_with_sheath = 0
support_material_xy_spacing = 75%
thin_walls = 1
threads = 8
top_fill_pattern = monotonic
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 40
top_solid_layers = 6
top_solid_min_thickness = 1.2
travel_speed = 120
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
xy_size_compensation = 0

[filament:Generic PLA @MEGA - Copy]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode ([filament_type], [notes])\n; \n; Filament-specific end gcode finish ([filament_type], [notes])"
extrusion_multiplier = 0.86
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 7.99
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 15
filament_minimal_purge_on_wipe_tower = 15
filament_notes = 0.55
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = Johns-PrusaSlicer-PLA-Profile-26-10-21
filament_soluble = 0
filament_spool_weight = 1000
filament_toolchange_delay = 0
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Made for Prusa
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 200
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 100
min_fan_speed = 80
min_print_speed = 10
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament-specific start gcode ([filament_type], [notes])\n; \n; Filament-specific start gcode finish ([filament_type], [notes])"
temperature = 195

[filament:Generic PLA StudioZombie3D]
bed_temperature = 60
bridge_fan_speed = 100
compatible_printers = 
compatible_printers_condition = 
compatible_prints = 
compatible_prints_condition = 
cooling = 1
disable_fan_first_layers = 1
end_filament_gcode = "; Filament-specific end gcode ([filament_type], [notes])\n; \n; Filament-specific end gcode finish ([filament_type], [notes])"
extrusion_multiplier = 0.86
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 7.99
filament_density = 1.24
filament_deretract_speed = nil
filament_diameter = 1.75
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 15
filament_minimal_purge_on_wipe_tower = 15
filament_notes = StudioZombie3D-Generic-PLA-Vyper
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = nil
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = nil
filament_retract_lift = nil
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = nil
filament_settings_id = Johns-PrusaSlicer-PLA-Profile-26-10-21
filament_soluble = 0
filament_spool_weight = 1000
filament_toolchange_delay = 0
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_vendor = Made for Prusa
filament_wipe = nil
first_layer_bed_temperature = 60
first_layer_temperature = 200
full_fan_speed_layer = 0
inherits = 
max_fan_speed = 100
min_fan_speed = 80
min_print_speed = 10
slowdown_below_layer_time = 10
start_filament_gcode = "; Filament-specific start gcode ([filament_type], [notes])\n; \n; Filament-specific start gcode finish ([filament_type], [notes])"
temperature = 195

[printer:Anycubic i3 Mega - Copy]
bed_custom_model = C:\\Program Files\\Prusa3D Beta\\VyperPrintBed.stl
bed_custom_texture = 
bed_shape = 0x0,250x0,250x255,0x255
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Generic PLA @MEGA"
default_print_profile = 0.15mm QUALITY @MEGA
deretract_speed = 40
end_gcode = G4 ; wait\nG92 E0\nG1{if max_layer_z < max_print_height} Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} ; move print head up\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200 F3000 ; home X axis\nM84 ; disable motors
extra_loading_move = -2
extruder_colour = #808080
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
machine_limits_usage = emit_to_gcode
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 1250
machine_max_acceleration_retracting = 1250
machine_max_acceleration_x = 1000
machine_max_acceleration_y = 1000
machine_max_acceleration_z = 200
machine_max_feedrate_e = 60
machine_max_feedrate_x = 200
machine_max_feedrate_y = 200
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.28
max_print_height = 265
min_layer_height = 0.1
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = M601
print_host = 
printer_model = I3MEGA
printer_notes = Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_VYPER\nPRINTER_HAS_BOWDEN
printer_settings_id = Johns-PrusaSlicer-PLA-Profile-26-10-21
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 1
retract_before_travel = 1.5
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 3
retract_length_toolchange = 10
retract_lift = 0.3
retract_lift_above = 0
retract_lift_below = 259
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG0 Z0.2 F1800 ; move nozzle to print position\nG92 E0 ; specify current extruder position as zero\nG1 Y10 X180 E50 F1200 ; extrude a line in front of the printer\nG92 E0 ; specify current extruder position as zero\nG0 Z20 F6000 ; move head up\nG1 E-7 F2400 ; retract\nG04 S2 ; wait 2s\nG0 X0 F6000 ; wipe from oozed filament\nG1 E-1 F2400 ; undo some of the retraction to avoid oozing\nG1 F6000 ; set travel speed to move to start printing point\nM117 Printing...\nG5
template_custom_gcode = 
thumbnails = 16x16,200x200
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[printer:StudioZombie3D_Vyper]
bed_custom_model = C:\\Program Files\\Prusa3D Beta\\VyperPrintBed.stl
bed_custom_texture = 
bed_shape = 0x0,250x0,250x255,0x255
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]
between_objects_gcode = 
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Generic PLA @MEGA"
default_print_profile = 0.15mm QUALITY @MEGA
deretract_speed = 40
end_gcode = G4 ; wait\nG92 E0\nG1{if max_layer_z < max_print_height} Z{z_offset+min(max_layer_z+30, max_print_height)}{endif} ; move print head up\nM104 S0 ; turn off temperature\nM140 S0 ; turn off heatbed\nM107 ; turn off fan\nG1 X0 Y200 F3000 ; home X axis\nM84 ; disable motors
extra_loading_move = -2
extruder_colour = #808080
extruder_offset = 0x0
gcode_flavor = marlin
high_current_on_filament_swap = 0
host_type = octoprint
inherits = 
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
machine_limits_usage = emit_to_gcode
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 1250
machine_max_acceleration_retracting = 1250
machine_max_acceleration_x = 1000
machine_max_acceleration_y = 1000
machine_max_acceleration_z = 200
machine_max_feedrate_e = 60
machine_max_feedrate_x = 200
machine_max_feedrate_y = 200
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_layer_height = 0.28
max_print_height = 265
min_layer_height = 0.1
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode = M601
print_host = 
printer_model = I3MEGA
printer_notes = Do not remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_ANYCUBIC\nPRINTER_MODEL_VYPER\nPRINTER_HAS_BOWDEN
printer_settings_id = Johns-PrusaSlicer-PLA-Profile-26-10-21
printer_technology = FFF
printer_variant = 0.4
printer_vendor = 
printhost_apikey = 
printhost_cafile = 
remaining_times = 1
retract_before_travel = 1.5
retract_before_wipe = 0%
retract_layer_change = 0
retract_length = 3
retract_length_toolchange = 10
retract_lift = 0.3
retract_lift_above = 0
retract_lift_below = 259
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = G21 ;metric values\nG90 ;absolute positioning\nM82 ;set extruder to absolute mode\nM107 ;start with the fan off\nG28 X0 Y0 ;move X/Y to min endstops\nG28 Z0 ;move Z to min endstops\nG0 Z0.2 F1800 ; move nozzle to print position\nG92 E0 ; specify current extruder position as zero\nG1 Y10 X180 E50 F1200 ; extrude a line in front of the printer\nG92 E0 ; specify current extruder position as zero\nG0 Z20 F6000 ; move head up\nG1 E-7 F2400 ; retract\nG04 S2 ; wait 2s\nG0 X0 F6000 ; wipe from oozed filament\nG1 E-1 F2400 ; undo some of the retraction to avoid oozing\nG1 F6000 ; set travel speed to move to start printing point\nM117 Printing...\nG5
template_custom_gcode = 
thumbnails = 16x16,200x200
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[presets]
print = StudioZombie_VyperV1
sla_print = 
sla_material = 
printer = StudioZombie3D_Vyper
filament = Generic PLA StudioZombie3D
physical_printer =